Claresa Extend Care 5 in 1 Keratin 1 Base Coat 5ml

is a reinforcing base enriched with keratin proteins. Extend Care Keratin 1 has a warm pink, peach-like color that is beautiful in itself or as a basis for Claresa UV/LED gellak. The Keratin 5 in 1 Extend Care Base Coat offers various advantages for the nails. The base coat creates smooth and well -groomed nails in an instant. The reinforcing proteins build the nail plate and make it possible to extend the nails to 1 centimeter. The Keratin Extend Care Base creates a protective layer over the nails against damage, splitting and breaking and supports the recovery of the nail. Use: Apply 1 or 2 thin layers on the nails depending on the condition of the nail. Hard the layer in 30-60 seconds in a UV/LED lamp. Then apply a color gellak of your choice and hard it under the lamp or immediately apply a Claresa Top Coat for a natural manicure. Let the gellak and top coat also cure under the UV/LED lamp. Read the full user manual and instructions for removing gellak at the bottom of this page. Harding time: UV LED lamp 6 W - 2 x 45 sec. UV LED lamp 9 W - 2 x 45 sec. UV LED lamp 48 W - 30 sec. UV LED lamp 60 W - 15 sec. UV lamp 36 W - 120 sec. Plus and minus points reinforcing base coat enriched with keratin proteins warm, peach peach color smooth and well-groomed nails in an instant, the damaged nail plate can again build up to 1 cm beautifully in itself or as a base coat for colored gellak quickly hardened under an UV/LED lamp. This is due to the color setting of the screen or lighting where the photo is taken. The color may also differ due to the top coat, such as when using a matte or a shiny top coat. Instructions for use: Step 1: Clean the nails and file them in the desired shape, Step 2: Remove the shine from the natural nails with a polishing block, Step 3: Push the backrons backwards with a goat and remove them with a cut belt tongs, Step 4: Make the nails clean and dust -free: STEP TO THE NAMERS. Wait until it is dry, this takes about 30 seconds, step 6: apply a thin layer of base coat and hard the nails under a lamp. Depending on the Basecoat 30-60 seconds under an LED lamp and 2-3 minutes under a UV lamp, step 7: Apply one thin layer of the hybrid gellak and hard the nails under a lamp. 30-60 seconds under an LED lamp and 2-3 minutes under a UV lamp, step 8: If desired, apply a layer of hybrid paint and repeat the above step until the desired coverage is reached, step 9: apply a topcoat and hard the nails under the lamp. 30-60 seconds under an LED lamp and 2-3 minutes under a UV lamp, Step 10: Then clean the nails with a cleaner to remove the sticky layer, step 11: Massage the skin around your nails as extra care with a caring nail cream or cuticle oil. Note: More pigmented colors, such as black and white, may require a longer curing time. It is important to apply these layers thinly and, if necessary, to paint and harden a second time to achieve the desired coverage. Removing the Claresa UV/LED Hybrid Soakoff Gel nail polish: Step 1: Carefully file the topcoat off the nails, Step 2: Soak a cotton pad in nail remover and place the cotton ball on the nails, Step 3: Make sure that the nail plate is completely covered. You can use nail remover foil for this. Wrap your finger firmly here, step 4: Check after a few minutes if the paint is loose. If this is not the case, wait a little longer, Step 5: When the gellak has been released, remove the remains with an Orange Woodstick, Step 6: After removing, use a hand cream and a cuticle oil for the optimum care of the hands. Ingredients: Dependythritolhexaacrylate, Hydroxypropylmethalate, Hema, Isobornylacrylate, Dimethylacrylamide, BIS (Methaloyyloxyethyl) phosphate, CI491, CITI-CI491, CITILOLOLYETYLE, BIS (Methacryyloxyethyl) BIS (metharyloyloxyethyl) BIS (Methaloyloxyethyl) Ci4911, CI4911, CI4911, CI491149114911, CI49141491191149114911491149114911, 778911491414911414914149141914149114914149191491491491491491491491491491495 77742, CI 77510 This article is only for professional use and can cause an allergic reaction.